К сожалению, фотографии внутренностей межсетевого экрана я не нашел, если у кого-нибудь есть возможность сфотографировать буду признателен.
Что находится «внутри»?
В устройстве используется пакетный процессор MIPS Broadcom XLP104B1. Пакетный процессор работает на частоте 400 MHz, SOC тоже на частоте 400 MHz.
Устройство оснащено памятью DDR3 объемом 4 ГБ.
Присутствует 128 битный биос - cmos serial MX25L12805D, объемом 16 МБ.
Для загрузки используется U-Boot.
Операционная система основана на программном коде Linux
Linux version 3.10.59 (skokov@ethlab-Aspire-4820T) (gcc version 4.6.3 (GCC) ) #30 SMP Mon Jul 10 09:42:23 MSK 2017
В составе продукта используется СПО - Open vSwitch.
Полные технические характеристики от производителя вы можете найти на официальном сайте.
Лог загрузки
Нажмите чтобы раскрыть
Нажмите чтобы закрыть
BRCM XLP Stage 1 Loader (X-Loader:1.0.7-ST.241) [Big-Endian] (Jun 21 2017 - 11:02:12)
XLP104B1: Node 0 frequency: CPU=400MHz, SOC=400MHz, REF=133MHz
POWER ON RESET CFG:30CE1FA8, VRM:6A, PRID:0xC1203
MBist Pass
DDR3: Node 0 Channel 0 Mem size = 4096 MB UDIMM, I2C: bus=0, addr=0x56
DDR3: Node 0 DRAM frequency 666 MHz
Board DDR VDD set to 1.5V.
N:0 Ch:0 m:40 s:40 R OK.
N:0 Ch:0 m:40 s:40 RW OK.
n:0 ch:0 addr mode:2T OK
Node:0 Ch:0 TGE Set Memory:4096 MB value:FF FF -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:FF 00 -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:AA 55 -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:00 00 -- PASS
DDR3 Initialization Passed.
DDR Interleave Mode: (node:0 chan:1)
NBU0 DRAM BAR0 base: 00000000 limit: 0013f000 xlate: 00000001 node: 00000000 ( 0|00000 MB -> 319|0013f MB, size: 320|00140 MB)
NBU0 DRAM BAR1 base: 001d0000 limit: 00bff000 xlate: 00090001 node: 00000000 ( 464|001d0 MB -> 3071|00bff MB, size: 2608|00a30 MB)
NBU0 DRAM BAR2 base: 00e00000 limit: 0128f000 xlate: 00290001 node: 00000000 ( 3584|00e00 MB -> 4751|0128f MB, size: 1168|00490 MB)
XLP watchdog timer: initialized
Hit any key to stop autoboot: 0
POWER ON RESET CFG:30CE1FA8
SPI: Got idcode c2 20 18 c2 20
0x4000 KiB MX25L12805D at 0:0 is now current device
Secure Boot ... Success
## Starting application at 0x8C100000 ...
BRCM.XLP.U-Boot:1.0.7-ST.241 (21/06/2017 - 11:02:24)
DRAM: 4 GB
Detected [XLP104B1]
Booted from SPI/MMC
CS0/CS1 -> OnBoard NOR/NAND
XLP watchdog timer: initialized
Now running in RAM - U-Boot [N64 ABI, Big-Endian] at: ffffffff8c100000
Ref Clk:133 MHz
Read FPGA from partition 'fpga0'
SF: Detected MX25L12805D with page size 256, total 16777216 bytes (DPB cleared)
Initializing FPGA: OK
## CFI Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
SF: Detected MX25L12805D with page size 256, total 16777216 bytes (DPB cleared)
Flash: 16 MB
NAND: ONFI flash detected
ONFI param page 0 valid
1024 MiB
Using default environment
In: serial
Out: serial
Err: serial
Reading factory settings...
SF: Detected MX25L12805D with page size 256, total 16777216 bytes (DPB cleared)
Factory settings:
factory_type:
factory_sn:
factory_mac:
factory_hw_ver:
Initialized I2C0 Controller.
Initialized I2C1 Controller.
Initialized I2C2 Controller.
Initialized I2C3 Controller.
Temp: MAX6657 temperature (int) 22 C
Temp: MAX6657 temperature (ext) 23 C
Temp: LM75 temperature 22 C
Hit any key to stop autoboot: 0
SF: Detected MX25L12805D with page size 256, total 16777216 bytes (DPB cleared)
0x4000 KiB MX25L12805D at 0:0 is now current device
byte at 0xa800000060000000 (0x02) != byte at 0xa800000060000004 (0x01)
Total of 0 bytes were the same
Total of 1 byte were the same
image-1
Device 0: nand0... is now current device
NAND read: device 0 offset 0x1440000, size 0x6400000
104857600 bytes read: OK
## Copying part 1 from legacy image at a800000060000000 ...
Verifying Checksum ... OK
Loading part 1 ... OK
## Copying part 0 from legacy image at a800000060000000 ...
Verifying Checksum ... OK
Loading part 0 ... OK
Version: 'integrity-verification-20170517'
Image Address: 0xa800000060000570
Image Size: 63936880 bytes
Value of the first bytes ELF header:
...
Signature address: a800000063ad3991
Hash:
...
Sign:
...
Public key:
...
verify_sign() return 0
Total time: 17 sec, 894 msec
U-Boot: GOST Signature Checking .... Success!
U-Boot: Secure Boot Checking .... Success
## Mapped entry address 0xffffffffc07aea60 -> 0xffffffff807aea60
## Starting application at 0xffffffff807aea60 ...
## Skipping init Ramdisk
DTB fixup ok.
Booting using OF flat tree...
[ 0.000000] Linux version 3.10.59 (skokov@ethlab-Aspire-4820T) (gcc version 4.6.3 (GCC) ) #30 SMP Mon Jul 10 09:42:23 MSK 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 000c1203 (Broadcom XLPII)
[ 0.000000] FPU revision is: 00771203
[ 0.000000] Checking for the multiply/shift bug... no.
[ 0.000000] Checking for the daddiu bug... no.
[ 0.000000] Node 0 - SYS/FUSE coremask 1
[ 0.000000] MIPS: machine is netlogic,XLP-FVP
[ 0.000000] Using DRAM BARs for memory map.
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 0000000010000000 @ 0000000000000000 (usable)
[ 0.000000] memory: 00000000a0000000 @ 0000000020000000 (usable)
[ 0.000000] memory: 0000000049000000 @ 00000000e0000000 (usable)
[ 0.000000] 2: Discarded 0x120000000 - 0x129000000
[ 0.000000] 8 TLB entires used for mapped kernel.
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] fdt copied to c000000003cc0000, size 11536
[ 0.000000] Reserved 32 MB at c000000003cc7ca0 on node 0 for fmn spill
[ 0.000000] software IO TLB [mem 0x05cd0000-0x06cd0000] (16MB) mapped at [c000000005cd0000-c000000006ccffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x00000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x11ffeffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0ffeffff]
[ 0.000000] node 0: [mem 0x20000000-0xbffeffff]
[ 0.000000] node 0: [mem 0xe0000000-0x11ffeffff]
[ 0.000000] Physical CPU mask: 00000000,00000000,00000000,0000000f
[ 0.000000] Possible CPU mask: 00000000,00000000,00000000,0000000f
[ 0.000000] node 0: 00000000,00000000,00000000,0000000f
[ 0.000000] Detected (1c4t) 4 Slave CPU(s)
[ 0.000000] Primary instruction cache 64kB, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB 4-way, VIPT, no aliases, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 2 pages/cpu @c000000007120000 s78848 r8192 d44032 u131072
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61374
[ 0.000000] Kernel command line: console=ttyS0,115200 rhash_entries=1048576 root=ramfs raid=noautodetect isolcpus=1-3 uboot=BRCM.XLP.U-Boot:1.0.7-ST.241 (date 21/06/2017 time 11:02:24) mtdparts=spi0.0:128k(x-loader),128k(factory)ro,1m(uboot),256k(env)ro,64k(firm),1m(fpga0)ro,1m(fpga1)ro,1536k(critlog);gen_nand.0:20m(config),256k(dtb),100m(vmlinux),100m(vmlinux2),500m(data) bootpart=1
[ 0.000000] PID hash table entries: 4096 (order: -1, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes)
[ 0.000000] Memory: 3809344k/3931968k available (6903k kernel code, 122624k reserved, 3275k data, 49984k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:1024
[ 0.000000] Init IRQ for node 0
[ 0.000000] PIC clock source added, frequency 200000000
[ 0.000000] MIPS counter frequency [800000000]
[ 0.000000] Console: colour dummy device 80x25
[ 0.004000] Calibrating delay loop (skipped) preset value.. 800.00 BogoMIPS (lpj=1600000)
[ 0.008000] pid_max: default: 32768 minimum: 301
[ 0.012000] Security Framework initialized
[ 0.016000] SELinux: Disabled at boot.
[ 0.016000] Mount-cache hash table entries: 4096
[ 0.020000] Initializing cgroup subsys net_cls
[ 0.024000] Checking for the daddi bug... no.
[ 0.028000] Performance counters: xlp PMU enabled, 4 64-bit counters available to each CPU, irq 6
[ 0.032000] CPU revision is: 000c1203 (Broadcom XLPII)
[ 0.032000] FPU revision is: 00771203
[ 0.036000] Synchronize counters for CPU 1: done.
[ 0.040000] CPU revision is: 000c1203 (Broadcom XLPII)
[ 0.040000] FPU revision is: 00771203
[ 0.044000] Synchronize counters for CPU 2: done.
[ 0.048000] CPU revision is: 000c1203 (Broadcom XLPII)
[ 0.048000] FPU revision is: 00771203
[ 0.052000] Synchronize counters for CPU 3: done.
[ 0.056000] Brought up 4 CPUs
[ 0.060000] devtmpfs: initialized
[ 0.064000] xor: measuring software checksum speed
[ 0.108000] 8regs : 1536.000 MB/sec
[ 0.148000] 8regs_prefetch: 1440.000 MB/sec
[ 0.192000] 32regs : 1568.000 MB/sec
[ 0.232000] 32regs_prefetch: 1456.000 MB/sec
[ 0.236000] xor: using function: 32regs (1568.000 MB/sec)
[ 0.240000] NET: Registered protocol family 16
[ 0.244000] Initializing 2XX USB Interface
[ 0.264000] XLP PCIe: Link 0-0 initialized.
[ 0.268000] XLP PCIe: Link 0-2 initialized.
[ 0.272000] XLP PCIe Controller [io 0x14000000-0x17ffffff][mem 0xd0000000-0xdfffffff].
[ 0.276000] Initializing XLP watchdog timer
[ 0.280000] bio: create slab at 0
[ 0.352000] raid6: int64x1 865 MB/s
[ 0.420000] raid6: int64x2 1075 MB/s
[ 0.488000] raid6: int64x4 716 MB/s
[ 0.556000] raid6: int64x8 402 MB/s
[ 0.556000] raid6: using algorithm int64x2 (1075 MB/s)
[ 0.560000] raid6: using intx1 recovery algorithm
[ 0.564000] SCSI subsystem initialized
[ 0.564000] usbcore: registered new interface driver usbfs
[ 0.568000] usbcore: registered new interface driver hub
[ 0.572000] usbcore: registered new device driver usb
[ 0.576000] pps_core: LinuxPPS API ver. 1 registered
[ 0.580000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <Этот адрес электронной почты защищен от спам-ботов. Для просмотра адреса в вашем браузере должен быть включен Javascript.>
[ 0.584000] PTP clock support registered
[ 0.588000] PCI host bridge to bus 0000:00
[ 0.592000] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xdfffffff]
[ 0.596000] pci_bus 0000:00: root bus resource [io 0x14000000-0x17ffffff]
[ 0.600000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.604000] pci 0000:00:01.0: PCI bridge to [bus 01-ff]
[ 0.608000] pci 0000:00:01.2: PCI bridge to [bus 02-ff]
[ 0.612000] Switching to clocksource PIC
[ 0.632000] NET: Registered protocol family 2
[ 0.636000] TCP established hash table entries: 32768 (order: 3, 524288 bytes)
[ 0.644000] TCP bind hash table entries: 32768 (order: 3, 524288 bytes)
[ 0.652000] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.656000] TCP: reno registered
[ 0.660000] UDP hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.668000] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.672000] NET: Registered protocol family 1
[ 24.396000] Node 0: registering 42 XLP GPIOs
[ 24.400000] audit: initializing netlink socket (disabled)
[ 24.404000] type=2000 audit(24.400:1): initialized
[ 24.416000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 24.424000] NTFS driver 2.1.30 [Flags: R/O].
[ 24.428000] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 24.432000] fuse init (API version 7.22)
[ 24.448000] msgmni has been set to 7440
[ 24.456000] async_tx: api initialized (async)
[ 24.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 24.468000] io scheduler noop registered
[ 24.472000] io scheduler deadline registered
[ 24.476000] io scheduler cfq registered (default)
[ 24.480000] usbcore: registered new interface driver udlfb
[ 24.484000] usbcore: registered new interface driver smscufx
[ 24.492000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 24.496000] 18030100.serial: ttyS0 at MMIO 0x18030100 (irq = 17) is a 16550
[ 24.504000] console [ttyS0] enabled, bootconsole disabled
[ 24.504000] console [ttyS0] enabled, bootconsole disabled
[ 24.516000] 18031100.serial: ttyS1 at MMIO 0x18031100 (irq = 18) is a 16550
[ 24.524000] xlp-drng 1802a000.rng: Registered xlp_drng RNG
[ 24.532000] brd: module loaded
[ 24.540000] loop: module loaded
[ 24.544000] ONFI param page 0 valid
[ 24.544000] ONFI flash detected
[ 24.548000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xa3 (Micron MT29F8G08ABBCAH4), 1024MiB, page size: 4096, OOB size: 224
[ 24.560000] 5 cmdlinepart partitions found on MTD device gen_nand.0
[ 24.568000] Creating 5 MTD partitions on "gen_nand.0":
[ 24.572000] 0x000000000000-0x000001400000 : "config"
[ 24.584000] 0x000001400000-0x000001440000 : "dtb"
[ 24.588000] 0x000001440000-0x000007840000 : "vmlinux"
[ 24.628000] 0x000007840000-0x00000dc40000 : "vmlinux2"
[ 24.668000] 0x00000dc40000-0x00002d040000 : "data"
[ 24.844000] xlp-spi 1803a000.xlp_spi: Registering for Node 0!
[ 24.852000] m25p80 spi0.0: mx25l12805d All DPBs cleared
[ 24.860000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 24.864000] 8 cmdlinepart partitions found on MTD device spi0.0
[ 24.868000] Creating 8 MTD partitions on "spi0.0":
[ 24.876000] 0x000000000000-0x000000020000 : "x-loader"
[ 24.880000] 0x000000020000-0x000000040000 : "factory"
[ 24.884000] 0x000000040000-0x000000140000 : "uboot"
[ 24.892000] 0x000000140000-0x000000180000 : "env"
[ 24.896000] 0x000000180000-0x000000190000 : "firm"
[ 24.900000] 0x000000190000-0x000000290000 : "fpga0"
[ 24.908000] 0x000000290000-0x000000390000 : "fpga1"
[ 24.912000] 0x000000390000-0x000000510000 : "critlog"
[ 24.920000] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 24.924000] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 24.928000] smsc911x: Driver version 2008-10-21
[ 24.936000] smsc911x 17200000.ethernet (unregistered net_device): couldn't get clock -2
[ 24.944000] PPP generic driver version 2.4.2
[ 24.948000] PPP BSD Compression module registered
[ 24.952000] PPP Deflate Compression module registered
[ 24.956000] PPP MPPE Compression module registered
[ 24.960000] NET: Registered protocol family 24
[ 24.964000] PPTP driver version 0.8.5
[ 24.968000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 24.976000] ehci-pci: EHCI PCI platform driver
[ 24.980000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 24.988000] xhci_hcd 0000:00:04.1: xHCI Host Controller
[ 24.992000] xhci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 25.000000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 25.008000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.012000] usb usb1: Product: xHCI Host Controller
[ 25.020000] usb usb1: Manufacturer: Linux 3.10.59 xhci_hcd
[ 25.024000] usb usb1: SerialNumber: 0000:00:04.1
[ 25.028000] hub 1-0:1.0: USB hub found
[ 25.032000] hub 1-0:1.0: 1 port detected
[ 25.036000] xhci_hcd 0000:00:04.1: xHCI Host Controller
[ 25.040000] xhci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
[ 25.048000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 25.056000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.064000] usb usb2: Product: xHCI Host Controller
[ 25.068000] usb usb2: Manufacturer: Linux 3.10.59 xhci_hcd
[ 25.072000] usb usb2: SerialNumber: 0000:00:04.1
[ 25.080000] hub 2-0:1.0: USB hub found
[ 25.084000] hub 2-0:1.0: 1 port detected
[ 25.088000] xhci_hcd 0000:00:04.2: xHCI Host Controller
[ 25.092000] xhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 3
[ 25.100000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 25.104000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.112000] usb usb3: Product: xHCI Host Controller
[ 25.116000] usb usb3: Manufacturer: Linux 3.10.59 xhci_hcd
[ 25.124000] usb usb3: SerialNumber: 0000:00:04.2
[ 25.128000] hub 3-0:1.0: USB hub found
[ 25.132000] hub 3-0:1.0: 1 port detected
[ 25.136000] xhci_hcd 0000:00:04.2: xHCI Host Controller
[ 25.140000] xhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 4
[ 25.148000] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 25.156000] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.164000] usb usb4: Product: xHCI Host Controller
[ 25.168000] usb usb4: Manufacturer: Linux 3.10.59 xhci_hcd
[ 25.172000] usb usb4: SerialNumber: 0000:00:04.2
[ 25.176000] hub 4-0:1.0: USB hub found
[ 25.180000] hub 4-0:1.0: 1 port detected
[ 25.184000] xhci_hcd 0000:00:04.3: xHCI Host Controller
[ 25.192000] xhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 5
[ 25.200000] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 25.204000] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.212000] usb usb5: Product: xHCI Host Controller
[ 25.216000] usb usb5: Manufacturer: Linux 3.10.59 xhci_hcd
[ 25.224000] usb usb5: SerialNumber: 0000:00:04.3
[ 25.228000] hub 5-0:1.0: USB hub found
[ 25.232000] hub 5-0:1.0: 1 port detected
[ 25.236000] xhci_hcd 0000:00:04.3: xHCI Host Controller
[ 25.240000] xhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 6
[ 25.248000] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[ 25.256000] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.260000] usb usb6: Product: xHCI Host Controller
[ 25.268000] usb usb6: Manufacturer: Linux 3.10.59 xhci_hcd
[ 25.272000] usb usb6: SerialNumber: 0000:00:04.3
[ 25.276000] hub 6-0:1.0: USB hub found
[ 25.280000] hub 6-0:1.0: 1 port detected
[ 25.284000] usbcore: registered new interface driver usb-storage
[ 25.292000] mousedev: PS/2 mouse device common for all mice
[ 25.604000] rtc-xlp 18035c00.rtc: rtc core: registered rtc-xlp as rtc0
[ 25.608000] i2c /dev entries driver
[ 25.620000] lm75 1-0049: hwmon0: sensor 'lm75_1'
[ 25.640000] md: raid0 personality registered for level 0
[ 25.644000] md: raid1 personality registered for level 1
[ 25.652000] md: raid6 personality registered for level 6
[ 25.656000] md: raid5 personality registered for level 5
[ 25.660000] md: raid4 personality registered for level 4
[ 25.668000] Unable to find Clock source for core0
[ 25.672000] sdhci: Secure Digital Host Controller Interface driver
[ 25.676000] sdhci: Copyright(c) Pierre Ossman
[ 25.720000] mmc0: SDHCI controller on xlp-mmc [0000:00:07.3] using ADMA
[ 25.724000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 25.732000] usbcore: registered new interface driver usbhid
[ 25.736000] usbhid: USB HID core driver
[ 25.740000] board: init driver
[ 25.748000] board: installed
[ 25.752000] SFP-HDLC Driver: init driver
[ 25.756000] SFP-HDLC Driver: installed
[ 25.760000] GACT probability on
[ 25.764000] Mirror/redirect action on
[ 25.768000] Simple TC action Loaded
[ 25.768000] u32 classifier
[ 25.772000] input device check on
[ 25.776000] Actions configured
[ 25.780000] ipip: IPv4 over IPv4 tunneling driver
[ 25.784000] gre: GRE over IPv4 demultiplexor driver
[ 25.788000] ip_gre: GRE over IPv4 tunneling driver
[ 25.796000] IPv4 over IPSec tunneling driver
[ 25.800000] TCP: cubic registered
[ 25.804000] Initializing XFRM netlink socket
[ 25.808000] NET: Registered protocol family 17
[ 25.812000] NET: Registered protocol family 15
[ 25.816000] l2tp_core: L2TP core driver, V2.0
[ 25.820000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 25.824000] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 25.832000] l2tp_netlink: L2TP netlink interface
[ 25.836000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 25.840000] 8021q: 802.1Q VLAN Support v1.8
[ 25.848000] sctp: Hash tables configured (established 65536 bind 65536)
[ 25.852000] Key type dns_resolver registered
[ 25.856000] XLP2xx Sysreg is 0x30ce1fa8
[ 25.860000] PCIE in RC Mode
[ 25.864000] registered taskstats version 1
[ 25.868000] rtc-xlp 18035c00.rtc: setting system clock to 2011-05-27 13:04:19 UTC (1306501459)
[ 25.900000] Freeing unused kernel memory: 49984K (ffffffffc0b00000 - ffffffffc3bd0000)
INIT: version 2.88 booting
Files under mount point '/dev/pts' will be hidden. ... (warning).
Setting hostname to 'esr-100'...done.
Activating swap:.
mount: according to mtab, tmpfs is already mounted on /lib/init/rw
Will now activate lvm and md swap:done.
Will now check all file systems.
fsck 1.41.12 (17-May-2010)
Checking all file systems.
Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
Will now mount local filesystems:mount: none already mounted or /sys busy
mount: according to mtab, sysfs is already mounted on /sys
failed!
Will now activate swapfile swap:done.
Conversion S-Terra config...OK
Cleaning up temporary files...Cleaning /tmp...done.
Cleaning /var/run...done.
Cleaning /var/lock...done.
.
Loading kernel module nae.
[ 33.084000] fdt_interface: module license 'unspecified' taints kernel.
[ 33.088000] Disabling lock debugging due to kernel taint
[ 33.096000] syslib: init library
[ 33.100000] Active Nodes: 1
[ 33.100000] xlp2xx: SAE/RSA engines disable
[ 33.100000] GBU Frequency set to 16MHz
[ 33.108000] syslib: init successfully
[ 33.116000] Going into legacy mode and using the dtb passed at boot time
[ 33.120000] Active Nodes: 1
[ 33.120000] xlp2xx: SAE/RSA engines disable
[ 33.120000] GBU Frequency set to 16MHz
[ 33.132000] Doing fmn init from cpu 0 for node 0
[ 33.136000] spillsize 0x2000000 @ 0x0000000010000000
[ 33.144000] node 0 default qsize 28672 credits 50
[ 33.148000] spill_base_cur 0x108b8000 qram_base_cur 0x1520
[ 33.152000] XLP304/204/104 FMN configuration
[ 33.160000] Validating credits configured for Node-0
[ 33.184000] datapath counters: 168 bytes per CPU
[ 33.196000] nf_conntrack version 0.5.0 (524288 buckets, 4194304 max)
[ 33.204000] netif_napi_add() called with weight 300 on device
[ 33.208000] fmn: allocated 1536 bytes for queues (384 per CPU, 96 per queue)
[ 33.280000] Invalid value nr-dcpu in fdt (1)
[ 33.292000] lb_wing table: 524288 buckets
[ 33.304000] lb_buffer table: 524288 buckets
[ 33.312000] nf_lb_orphan table: 524288 buckets
[ 33.320000] ======= Module Parameters =========
[ 33.324000] nae debug mask 0x1
[ 33.324000] num_descs_per_normalq=2298 num_descs_per_jumboq=2298 perf_mode=ESR_PERF dsa_mode=0 enable_lro=0 enable_jumbo=1
[ 33.336000] hw_repl_mode=0
[ 33.340000] BRCM HAL net confgured for xlp2xx
[ 33.344000] init_netsoc dom 0Unable to find the frequency in the FDT file for type:6, using the default value
[ 33.356000] Complex 0 in SGMII mode
[ 33.364000] fdt_parse_port_config numports 4 numcontexts 4
[ 33.368000] BRCM NETSOC Max NAE: 1 POE 1 ALE 0
[ 33.372000] BRCM NETSOC FEATURES: 0x3f
[ 33.380000] Stopping and Resetting all ucore...
[ 33.384000] Ucore Reset Complete
[ 33.388000] Loading ucores (mask = 0x00ff)
[ 33.396000] PMA2P0 configuration is OK
[ 33.400000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
[ 33.412000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
[ 33.420000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
[ 33.432000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
[ 33.444000] BCM54240_INIT_PHY: port 0, phy address 0x0
BCM54240_INIT_PHY: port 1, phy address 0x1
BCM54240_INIT_PHY: port 2, phy address 0x2
BCM54240_INIT_PHY: port 3, phy address 0x3
NAE frequncy set to = 250Mhz__netsoc_init_poe
[ 34.816000] POE Free Buffer Pool config ...
[ 34.868000] POE Configuring Message base pointer base_lo 0xf4800040 hi 0x0
[ 34.876000] POE Configuring FBP base pointer fbp_lo 0x18120040 hi 0x1
[ 34.884000] POE Configuring FBP stack pointer 0x380
[ 34.888000] enabling poe drop based on dist vec
[ 34.892000] DONE WITH INIT NETSOC #######
[ 34.896000] DONE WITH INIT POE #######
[ 34.900000] Stopping and Resetting all ucore...
[ 34.904000] Ucore Reset Complete
[ 34.908000] Loading ucores (mask = 0x00ff)
[ 34.912000] initialize_nae done
[ 34.944000] Registering nae datapath handler
[ 34.960000] PCI: Enabling device 0000:00:03.0 (0000 -> 0002)
Loading kernel module module_licence.
[ 34.968000] ! Licence manager init!
Loading kernel module gre_nfqueue.
Loading kernel module nf_conntrack_ipv4.
Loading kernel module nf_conntrack_tftp.
Loading kernel module nf_conntrack_sip.
Loading kernel module nf_conntrack_pptp.
Loading kernel module nf_conntrack_netbios_ns.
Loading kernel module nf_conntrack_ftp.
Loading kernel module nf_conntrack_h323.
Loading kernel module nf_conntrack_proto_gre.
Loading kernel module nf_nat_tftp.
Loading kernel module nf_nat_sip.
Loading kernel module nf_nat_pptp.
Loading kernel module nf_nat_ftp.
Loading kernel module nf_nat_h323.
Loading kernel module nf_nat_proto_gre.
Loading kernel module ipt_CONNTC.
Loading kernel module openvswitch.
[ 35.088000] openvswitch: Open vSwitch switching datapath 2.3.0, built Jun 15 2017 13:19:35
Checking minimum space in /tmp...done.
Setting kernel variables ... /etc/sysctl.conf...done.
Initializing random number generator...done.
Trying to load drivers:
cryptopm: done.
vpndrvr: done.
cp_plg1: done.
cp_aes: done.
st_gost: done.
Configuring IPsec driver:
Starting vpnsvcwd_daemon...done.
INIT: Entering runlevel: 3
Find config file on mnt, load path = /mnt/config/etc/config/esr/syslog-ng.conf
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] Checking for the multiply/shift bug... no.
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] Checking for the daddiu bug... no.
2011-05-27T13:04:29+00:00 syslog-ng starting up; version='3.2.3'
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] Zone ranges:
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] DMA32 [mem 0x00000000-0xffffffff]
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] Normal [mem 0x100000000-0x11ffeffff]
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] Movable zone start for each node
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] Early memory node ranges
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] node 0: [mem 0x00000000-0x0ffeffff]
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] node 0: [mem 0x20000000-0xbffeffff]
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] node 0: [mem 0xe0000000-0x11ffeffff]
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61374
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.024000] Checking for the daddi bug... no.
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.352000] raid6: int64x1 865 MB/s
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.420000] raid6: int64x2 1075 MB/s
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.488000] raid6: int64x4 716 MB/s
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.556000] raid6: int64x8 402 MB/s
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.556000] raid6: using algorithm int64x2 (1075 MB/s)
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 0.560000] raid6: using intx1 recovery algorithm
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 24.936000] smsc911x 17200000.ethernet (unregistered net_device): couldn't get clock -2
2011-05-27T13:04:29+00:00 %SYSTEM-C-KERNEL: [ 25.668000] Unable to find Clock source for core0
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 25.740000] board: init driver
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 25.748000] board: installed
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 25.752000] SFP-HDLC Driver: init driver
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 25.756000] SFP-HDLC Driver: installed
2011-05-27T13:04:29+00:00 %SYSTEM-E-KERNEL: [ 25.860000] PCIE in RC Mode
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.084000] fdt_interface: module license 'unspecified' taints kernel.
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.088000] Disabling lock debugging due to kernel taint
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.096000] syslib: init library
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.100000] Active Nodes: 1
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.100000] xlp2xx: SAE/RSA engines disable
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.100000] GBU Frequency set to 16MHz
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.108000] syslib: init successfully
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.120000] Active Nodes: 1
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.120000] xlp2xx: SAE/RSA engines disable
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.120000] GBU Frequency set to 16MHz
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.136000] spillsize 0x2000000 @ 0x0000000010000000
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.144000] node 0 default qsize 28672 credits 50
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.148000] spill_base_cur 0x108b8000 qram_base_cur 0x1520
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.152000] XLP304/204/104 FMN configuration
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.160000] Validating credits configured for Node-0
2011-05-27T13:04:29+00:00 %SYSTEM-E-KERNEL: [ 33.204000] netif_napi_add() called with weight 300 on device
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.208000] fmn: allocated 1536 bytes for queues (384 per CPU, 96 per queue)
2011-05-27T13:04:29+00:00 %SYSTEM-E-KERNEL: [ 33.280000] Invalid value nr-dcpu in fdt (1)
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.320000] ======= Module Parameters =========
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.324000] nae debug mask 0x1
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.324000] num_descs_per_normalq=2298 num_descs_per_jumboq=2298 perf_mode=ESR_PERF dsa_mode=0 enable_lro=0 enable_jumbo=1
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.336000] hw_repl_mode=0
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.340000] BRCM HAL net confgured for xlp2xx
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.344000] init_netsoc dom 0Unable to find the frequency in the FDT file for type:6, using the default value
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.356000] Complex 0 in SGMII mode
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.364000] fdt_parse_port_config numports 4 numcontexts 4
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.368000] BRCM NETSOC Max NAE: 1 POE 1 ALE 0
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.372000] BRCM NETSOC FEATURES: 0x3f
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.380000] Stopping and Resetting all ucore...
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.384000] Ucore Reset Complete
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.388000] Loading ucores (mask = 0x00ff)
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.396000] PMA2P0 configuration is OK
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.400000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.412000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.420000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.432000] xlp2xx_set_pll_dividers: RefClk=0 or not set, skipping PLL dividers config
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.444000] BCM54240_INIT_PHY: port 0, phy address 0x0
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.444000] BCM54240_INIT_PHY: port 1, phy address 0x1
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.444000] BCM54240_INIT_PHY: port 2, phy address 0x2
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.444000] BCM54240_INIT_PHY: port 3, phy address 0x3
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 33.444000] NAE frequncy set to = 250Mhz__netsoc_init_poe
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.816000] POE Free Buffer Pool config ...
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.868000] POE Configuring Message base pointer base_lo 0xf4800040 hi 0x0
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.876000] POE Configuring FBP base pointer fbp_lo 0x18120040 hi 0x1
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.884000] POE Configuring FBP stack pointer 0x380
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.888000] enabling poe drop based on dist vec
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.892000] DONE WITH INIT NETSOC #######
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.896000] DONE WITH INIT POE #######
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.900000] Stopping and Resetting all ucore...
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.904000] Ucore Reset Complete
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.908000] Loading ucores (mask = 0x00ff)
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.912000] initialize_nae done
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.944000] Registering nae datapath handler
2011-05-27T13:04:29+00:00 %SYSTEM-W-KERNEL: [ 34.960000] PCI: Enabling device 0000:00:03.0 (0000 -> 0002)
Running local boot scripts (/etc/rc.local)Starting the hotplug events dispatcher udevd
Starting pcscd
.
2011-05-27T13:04:29+00:00 36.312000] udevd[385]: starting version 175
2011-05-27T13:04:30+00:00 %SYSTEM-W-KERNEL: [ 36.808000] board: watchdog: registered
2011-05-27T13:04:30+00:00 %SYSTEM-W-KERNEL: [ 36.808000] board: watchdog: comm: [top-mgr] pid: [412]
2011-05-27T13:04:30+00:00 %TOP-I-REGPROCESS: service 'Cp-mgr' was started, pid = 420
2011-05-27T13:04:30+00:00 %TOP-I-REGPROCESS: service 'Service-mgr' was started, pid = 446
2011-05-27T13:04:30+00:00 %TOP-I-REGPROCESS: service 'Session-mgr' was started, pid = 423
2011-05-27T13:04:30+00:00 %TOP-I-REGPROCESS: service 'Ipc-hub' was started, pid = 414
2011-05-27T13:04:30+00:00 %TOP-I-REGPROCESS: service 'Env-mgr' was started, pid = 435
2011-05-27T13:04:30+00:00 %ENV-W-FAN: Fan level is now 73%
2011-05-27T13:04:30+00:00 %TOP-I-REGPROCESS: service 'Alarm-mgr' was started, pid = 434
2011-05-27T13:04:30+00:00 %TOP-I-REGPROCESS: service 'Lb' was started, pid = 424
[ 37.268000] l3cam mask :0 0x476f2f40
[ 37.272000] l3cam even 0 : 0x950800
[ 37.276000] l3cam odd 0 : 0x30881064
[ 37.280000] Enabling parser for nae node 0 naeid 0
[ 37.284000] rx config 0x437939e1
2011-05-27T13:04:31+00:00 %SYSTEM-C-KERNEL: [ 37.268000] l3cam mask :0 0x476f2f40
2011-05-27T13:04:31+00:00 %SYSTEM-C-KERNEL: [ 37.272000] l3cam even 0 : 0x950800
2011-05-27T13:04:31+00:00 %SYSTEM-C-KERNEL: [ 37.276000] l3cam odd 0 : 0x30881064
2011-05-27T13:04:31+00:00 %SYSTEM-C-KERNEL: [ 37.280000] Enabling parser for nae node 0 naeid 0
2011-05-27T13:04:31+00:00 %SYSTEM-C-KERNEL: [ 37.284000] rx config 0x437939e1
2011-05-27T13:04:34+00:00 %ENV-W-FAN: Fan level is now 33%
Setting hostname to 'esr-100'...done.
2011-05-27T13:04:52+00:00 %SYS-W-EVENT: Configuration is applied
S-Terra administrative console
login as:
Заключение
Вот и всё. Много информации из лога вытащить не удалось, но и эта информация может быть любопытна системным администраторам и IT-специалистам.